Sunday, December 19, 2010

Florida Music quality M8 music player balanced sets Guinness

First, the tuning is a very subjective, is known in the industry, a music-and-drop out, as long as it is a perfect player can't go about setting EQ EQ, once set, it cannot fully restore the recording would like to express the music of the highest artistic conception. But now the player can $ at the frequency section are balanced expressed almost to zero. So we need to adjust EQ to remedy the defects, the following M8 we step by step, tuning can not be impatient. First step, we first plug in the headphones, turn off his first wife, placed a first EQ hivi T200A try yindie (Thunder can), APE format, this disc has 54 minutes, ten song must be heard. After listening to your basic understanding of this player flaws and strengths. It can be said that the M8 plug in headphones to play music, it's in the treble and treble still can, the worst part is the bass, this is mainly due to the defects of the headphones M8, the headphones, it is not, then 40HZ 40HZ to 200HZ also do not put in place, so when kerosene are listening to will feel the bass baritone parts rarely, can also be said to be so bad, if we are willing to spend money to buy a cost a headset to listen to, there is no need to set EQ, but I believe the M8 players like me a Moonlight family absolute majority, or help you tone up, saving some money. Second step, have to do the analysis about M8, nor do deeper, if I were to tell you too deep, you may only see the Holy Scriptures of kerosene. Now we have a section of a paragraph to debug, M8 of EQ is divided into 10 segments. First paragraph, this is in part due to the subwoofer, M8 headphones that paragraph did not, therefore, can the appropriate decay 1 DB, because it does not do this, once this section to show it is noisy. Second paragraph, bass part, but the part near the subwoofer, for people who hardly no see, give you the feeling of simply shake, but shaking too much too little is not good, so I fixed it. Third paragraph, bass, but accurate, it is the starting point in the bass, can raise two DB, this music sounds relatively thick, makes up for the bass part. Fourth paragraph, middle position in the bass, reasonable upgrade that three decibels, so that the music sounds are, in particular all drum sounds very comfortable. Fifth paragraph, bass, voice from the end of the fourth paragraph to paragraph 6, that paragraph must decay 2 DB. This sounds mellow, the human voice. Sixth paragraph, baritone parts 1KHZ, this will not move it too little, too much is bad. Because the performance is M8 headphones from this period until 20KHZ, expressive farther on, the better. Seventh paragraph, treble section of this part to decay 2 decibels, M8 headphones in this part of the expression is quite strong, but this part too many sounds too bright, but failure too much it sounds boring, dazzling music cannot sense. 8 attenuate, this part of the 3 DB, this part too many harsh, headphones and more expressive power of this part are strong, so to decay. Ninth paragraph, fixed, because this section of the performance of the M8 headphones still good, but not too much, and I'm very clear sense of depth. Tenth paragraph, upgrade 2 DB, because this is UHF segment, can properly upgrade, on the human brain is good, people are listening to the music of time does not feel bored, stunning. Third step, complete. We slowly enjoy!

Again. This type of transfer method is only suitable for M8 wife headset, if the headset and the other transfer method.

The figure for balanced setting example diagrams

The figure for a variety of settings parameters

Here are the new meizu reveal UI and official release of the new UI of the method:

Meizu's new UI only 63,250, 1K, 4K, 16K five options, you can also set the corresponding little difference, in other words if you are a compromise version of the firmware, you can directly overlook 31,125,500, 2K, 8K not later, on the treble and bass are in sound settings page of the previous menu

The figure for the new UI debug parameters

The figure for the new UI debug parameters

No comments:

Post a Comment